Dedicated Recirc System - Standard Coupon Code
   FREE SHIPPING NOW AVAILABLE ON ALL ITEMS.







Dedicated Recirc System
Tankless Controller

Hot Water Circulation System

$197.00

For Use With:
Water Heater: Traditional Tank or Tankless
Hot Water Return Line: Yes

Model Number: DRS-TC
Free Shipping in US
Product Overview | Tankless Installation & Operation | Tank Information
Product Overview

The Dedicated Recirc System converts a hot water circulation line into an efficient on-demand delivery system.

The Dedicated Recirc System delivers hot water only when there is a demand:

  • Reducing Energy Costs &
  • Virtually Eliminating Pinhole Leaks

When the Flow Monitor detects a hot water demand the Pump Manager turns on your existing pump and rushes water out to where it is needed.

The Pump Manager will run the pump for approximately 3 minutes to ensure that hot water is available throughout your home. (adjustable from 1 second to 167 hours)

Pump Manager
Flow Monitor
Return to Top
Installation

Step 1. Inspect your existing pump:

If the pump has not been operating properly or shows any visible signs of wear it may need to be replaced.

Step 2. Turn off water heater:

Turn off water heater to make sure it does not come on during installation.

Step 3. Turn off water:

Turn off the water to the water heater. In most cases there is a valve located near the water heater on the cold water supply line.

Step 4. Drain the hot water lines:

Turn on any hot water faucet in the house and let it run until the water stops flowing. Leave the faucet on for the duration of the installation. Drain remaining hot water using the hot water spigot on the water heater.

Note: If water continues to flow, check to make sure that the water has been completely turned off. If the valve does not shut off the water flow completely turn off the valve supplying water to the house or at the water meter.

Step 5. Cut the cold water feed to the water heater where the Flow Monitor is to be installed:

Remove a section of pipe equivalent to the length Flow Monitor plus any extra length for required fittings.

Return to Top

Step 6. Orientation of the Flow Monitor:

Make sure the arrows on the Flow Monitor are pointing in the direction of flow.

Step 7. Existing pump:

Correct installation of the pump can be either horizontal or vertical. Use proper straps for support if necessary.


Outdoor Installation Picture

Return to Top

Step 8. Install the Flow Monitor:

Make sure the gasket is inserted in the female end of the Flow Monitor. Do not over tighten.

Step 9. Complete connections and turn on water:

Make sure that a hot water faucet is turned on in the house and then slowly turn the water back on to the water heater. Check for leaks and repair as necessary. Leave the water running until all of the air has been purged from the water pipes. Turn off the faucet.

Step 10. Connect the Pump Manager and the Flow Monitor:

Connect the wires from the Flow Monitor to the wires from the Pump Manager.

Circulation pump switch

Set pump toggle switch to III (3 bars) setting for the highest speed.

Return to Top

Step 11. Plug the pump in:

Plug the pump into the Pump Manager and plug the Pump Manager into a properly grounded 110 vAC outlet.

Step 12: Test Dedicated Recirc System:

Turn on any hot water faucet in the house for 1 second and turn it off. Pump should continue to operate for approximately 3 minutes after the faucet has been turned off.

Note: The 3 minutes will not start until all demand for hot water has ended.


Electrical Information

Safety Warning

Risk of Electrical Shock

This pump is supplied with a grounding conductor. To reduce the risk of electrical shock, be certain that it is connected only to a properly grounded grounding type receptacle.

The safe operation of this pump requires that it be grounded in accordance with the national Electrical Code and local government regulations.

Operating Instructions


To activate the Dedicated Recirc System, simply turn on any hot water faucet in the house and quickly turn it off.

This will start the pump which will run for approximately 60 seconds. Typically it takes about 10 to 15 seconds to heat up the entire circulation line. Once the line is hot you will have hot water everywhere you want it.

The pump will shutoff approximately 60 seconds after the demand for hot water ends.


Installation Notes:

The Dedicated Recirc System can be used with both tank style water heaters and tankless water heaters. These instructions are for installation on a tankless water heater. Please refer to the appropriate manual for tank style installations.

A portion of the Dedicated Recirc System is installed in the cold water line in or the hot water line out of a tankless water heater. Failure to follow these instructions may lead to system failure and/or property damage. Although a plumber is not required to install the system familiarity with basic plumbing is necessary.

If you have any questions, or if you need more information please give us a call or text us at (619) 665-2077, or email us at:

Return to Top